DIY Raised Bed Trellis

comments (6) May 20th, 2011

Pin It

yourownvictorygarden Greg Holdsworth, contributor
thumbs up 31 users recommend

Click To Enlarge Photo: Greg Holdsworth

With Spring moving right along and Summer hiding around the corner, your veggies should (hopefully) be growing well. In the case of your vining crops—cucumbers, pole beans, and some melons—they undoubtedly will need some support at some point. If you are using a raised bed system in your garden, you have to use your space wisely.

  DIY Trellis
Photo A

DIY Trellis
Photo B

DIY Trellis
Photo C

DIY Trellis
Photo D

DIY Trellis
Photo E

DIY Trellis

  Photo F
DIY Trellis
  Photo G
DIY Trellis
  Photo H
DIY Trellis
  Photo I
DIY Trellis
  Photo J
DIY Trellis
  Photo K
In my previous article on trellises, I identified the advantages and types of trellises and how they can use vertical space efficiently in your garden. This project uses the "wall" type trellis, which is fairly common.

What makes this project a little different is not the type of trellis, but how the string is applied. Anyone can order a plastic net, go out to your trellis frame with staple gun (or worse, hammer) in hand, hope it's the right size, and put it up. This application, however, borrows from the game of tennis. That's right friends... we'll be stringing our trellis like a tennis racquet!

The advantages of doing it this way are:

1. You can control the type and spacing of your strings; 2. You don't beat up the sides of your trellis with staple and nail holes; and 3. You can control how tight the strings are, and adjust them as necessary as the season goes along.

"But that seems like too much time and trouble," I can imagine you asking me. I was actually surprised as to how quickly the strings went up. I completed the stringing of the 5' x 5' trellis you see in the photos in less than an hour. And that was doing it alone and stopping to take photos.

For this project I used cedar for my trellis frame, for both it's beauty and longevity. At the moment it's kinda standing out next to the raised bed it's attached to (made from regular plywood); but this is temporary, as I will be replacing my beds with cedar next year.


The list of things you'll need:

• 2 - 2" x 3" or 2" x 4" wood 'posts', 4 to 5 feet long (the length of your raised bed) (Photo A)

• 2 - 2" x 3" or 2" x 4" wood 'posts', 5 to 7 feet long (determined by how tall you want your trellis) (Photo A)

• 4 - 1.5" metal angle brackets (#1, Photo B)

• 4 - 3" metal angle brackets (#2, Photo B)

• 1 - box of #8 1 3/4" wood screws, 50 or 100 quantity (which is more than you'll use, but they're cheaper that way) (Photo C)

• 1 - ball of string/twine, at least 200-300 feet length (Photo C)

• Drill & drill bits

• Measuring tape

• Saw

• Pencil

Skill Level:

Easy to intermediate, depending on your wood building skills.


1. Measure the height of your raised bed, as well as the length of the side the trellis will be mounted to. For the purposes of this post, my raised beds are approximately 5 feet wide by 5 feet long by 10" high.

2. Cut TWO of the four 2x3's/2x4's to the width of your raised bed, MINUS twice the thickness of your raised bed's sides. That way the trellis will correctly match the raised bed's width.

3. Then, cut the remaining two of the 2x3's/2x4's to the height you wish your trellis to be. You'll end up with 4 pieces, two different matching lengths (Photo A).

4. Gather up your hardware - brackets, screws, drill, etc.

5. Arrange the four pieces as they will be put together (Photo D). The distance of the bottom horizontal piece from the end of the posts is determined by the height of your raised bed.

6. Place the bracket where two of the wood pieces meet in the corner. While holding it in place, mark the holes with a pencil (Photo E).

7. While holding the bracket and wood together, drill the holes, and put in the screws (Photo F). Repeat for the remaining 3 corners.

8. The trellis frame is now complete. Now it's time to drill the string holes. Measure and mark the holes with a pencil on all sides. For my trellis, I went with 15 holes, spaced 4 inches apart (Photo G).

9. Drill your string holes with a hole large enough to easily feed the string through (at least a 1/4") (Photo H).

10. Place the trellis next to your raised bed. Using the four 3" angle brackets (two for each side), screw the trellis to the side of the raised bed (Photo I).

11. Here's where the "tennis racquet" part comes in. Feed the string through the leftmost hole and feed it down to its corresponding hole at the opposite end of the trellis. In other words, if you started at the bottom, you'll be going up to the corresponding hole at the top. (Photo J).

12. Pull the string all the way through that hole, then loop it back into the hole next to it. Again, pull it through to its corresponding hole on the opposite end.

13. Repeat this process until you've gone all the way across the width of the trellis.

14. Now continue with the horizontal strings, by going top to bottom. When finished, you should now have a nice grid of string squares (Photo K).

Your trellis is pretty much ready to go at this point.

Mounting it to the side of the raised bed should provide enough support, not only against winds, but the weight of your vining veggies. If the winds in your area are typically stronger than average, you may need to reinforce the trellis. This could be done by screwing in additional posts to connect the trellis to the raised bed at a 45-degree angle.

I have included a schematic illustration of the trellis to assist with construction. You can download it here. Enjoy and good luck!


After you try it, show it off to other members in the
gardener's gallery.
Post your photos

posted in:

Comments (6)

VaneelaCharon writes: Excellent info
Posted: 1:57 am on May 25th
ThisOldBob writes: I made the same type of frames using 2x2 and 1x2 and some 4' wide 2x3 green coated wire fencing. I first made the frame 4' wide using the 2x2 and some angle brackets. Then I laid the 4' wide wire fencing over the frame. It fit flush to the outside edge of the frame. Next I laid the 1x2 over the fencing and sandwiched it all together with some 2" exterior screws in pre-drilled holes through the 1x2s into the 2x2s. They've been together now for about 10 years and used for cucumbers, pole beans and even espalier of a sungold cherry tomato. I even made an extra frame 4'x4'that I attached to the top of the one used for pole beans and diagonally braced it to the uprights at the four corners with 2' pieces of 2x2 to make the T shaped trellis to grow the pole beans on. Then you can just walk under and pick away both in front of you and right over your head.
Posted: 10:20 am on February 24th
bobbyevans6 writes: Really nice
Posted: 1:43 am on January 2nd
thyme4tea writes: Instead of strings, and for a more permanent structure, I suggest concrete reinforcing wire. It has 4" square openings, so could be used for a variety of vegetables. I use mine for cucumbers and (In a circle) for tomatoes. (It is not constructed as well as this one...I'll be changing mine this spring!) Thanks.
Posted: 11:16 am on February 4th
Miracles_255 writes: Thank you so much for this article. What a great project! I built a 6X8 version of this today and I used twine. It broke a few times and it seems brittle, I have threads all over the yard. Are you sure this stuff is okay to use to hold up vines? I want to use it to support melons.
Posted: 10:08 pm on May 4th
ntarte writes: I'm wondering how wide a trellis one could make without needing a center pole for reinforcement.
Posted: 8:56 am on January 22nd
Log in or create a free account to post a comment.