Setting Up A Garden Drip Irrigation System

comments (2) June 26th, 2013

Pin It

yourownvictorygarden Greg Holdsworth, contributor
thumbs up 35 users recommend

The main supply lines can be above or below ground. You may want to keep them above until everything is working smoothly.
A plastic tub keeps all of the parts and tools organized.
A quick connect kit is a godsend for saving time.
Click To Enlarge Photo: Greg Holdsworth (All photos)

Summer has just begun officially, and we are already knocking on the door of triple digit temperatures. I can't be out in the garden more than ten minutes before I start to sweat, and the crackling noise you hear are my shoes cooking on the mulch between my raised beds. I can't imagine how the plants in my garden must be feeling. Without regular, consistent watering, it's a safe bet that the plants in my garden would suffer dramatically.

To prevent this from happening, I set up a drip irrigation system about this time last year. It went through systematic changes and repairs along the way, of course. It had to be partially disassembled over the Winter, as I had rebuilt two of my raised beds and added a third. I got it back online a couple of weeks ago, just in time for the first 90+ degree temperatures to hit. The following are general thoughts and tips that I picked up in the process of building and maintaining my drip irrigation system.

Plan it out.
Since you already had a plan in the Spring of how your garden was gonna lay out (you did have one, didn't you?), this step should be pretty straightforward. Draw out, almost in mind-mapping-like fashion, how you are going to get water to each of your planting beds. Whether they are raised or not, you have to consider the distance to the water source (faucet, rail barrels, etc.). Will it stay on top, or will you need to bury it when everything is connected? Will one "zone" be enough? 

Start small, but keep expansion and time in mind.
I realize I'm writing this after Summer has officially begun, so it's already hot out. I'm actually referring to dividing the job into more manageable pieces if the system needs to cover a lot of ground. When my drip system was going in, three of my raised beds didn't have anything in them, so those could be worked on later in time for Fall plantings. All I needed to put in to those areas were the main lines. If you are putting in a new bed, adding the drip system before or when you're putting in plants is easier than afterwards.

Change out your "ends" easily.
Your drip system will probably take care of most of your watering needs, but you may still need to use a hose-end hand or wand sprayer. Quick connect kit to the rescue! I wish I had learned about this very inexpensive, major-time-saving tool years ago. A quick connect kit allows you to quickly switch out sprayers or other watering devices. Here's the awesome part – you can do it without even turning off the water! So in my case, the main hose to the faucet can quickly be disconnected from the drip system and reconnected to my hand-held wand to water potted plants, wash out containers, etc.

Keep it organized.
I discovered very quickly that the drip system had lots of parts to it, in addition to any tools needed to put them together. Knowing how much of each part you have, or how much drip hose you have left, can certainly eliminate extra unwanted trips to the hardware store. My solution was to simply get a small clear plastic bin with a lid to put it all in. That way, if it's time to fix or add something, everything you need comes with you to the garden. 

Baby it at first.
OK, so it's the moment of truth. You've got everything hooked up and are ready for testing. I would definitely recommend turning the water on slowly, and increasing the pressure very gradually. Once everything looks good, it's time to let it run for a while (30 minutes to an hour). You're checking for consistent water flow, coverage, and for faulty hoses. It may take 2 or 3 days of watering to really see how everything's working.

The greatness of the timer.
The best money I put into the drip system was not actually the system itself. It was the automatic timer that controlled it. The reduced stress and time savings payed for it many times over. When choosing one, pick one that allows you to very finely control when and how long the watering occurs. It should have a good factory warranty, and I know you'll hang on to the store receipt. The timer on my system is currently set to water at 6 (a.m.) and 6 (p.m.). If your city has watering restrictions (like mine), you'll have to consider those as well.

Setting up a drip system is a very worthwhile investment, and can be done fairly easily. Your veggies will thank you for it!

 

 

 

 


After you try it, show it off to other members in the
gardener's gallery.
Post your photos

posted in: watering, Water, drip irrigation, drip system

Comments (2)

hfmfg writes: I used a really affordable drip irrigation system from H&F Manufacturing that required very minimal assembly on my part. These irrigation systems are a great way to leave your garden on auto-pilot, and they require very little maintenance if they’ve been setup properly in the first place. It definitely takes some time to get it going at first, but if you take a day in the early spring to get it done, you’ll reap that time back all through the spring and summer seasons.
Posted: 10:58 am on March 25th
vino_fiendo writes: Valuable topic... but probably the least informative article I have ever read... just a lot of fluff with no details, links etc. "where's the beef"?? PLEASE... someone bring your 'A' game. Thanks
Posted: 8:59 am on July 3rd
Log in or create a free account to post a comment.