Build Your Own Classic Compost Bin

comments (18) June 18th, 2014

Pin It

yourownvictorygarden Greg Holdsworth, contributor
thumbs up 5 users recommend

PHOTO A
PHOTO B
PHOTO C. Drawing a line on the side of the two pieces will provide a guide for the angle of the screw.
PHOTO D. The finished side panel, ready for the hardware cloth.
PHOTO E. You can use the back of a business card as a template for marking the holes for the hook-and-eye latches.
PHOTO F. The hook-and-eye latch in place.
PHOTO G. The finished bin, ready for composting.
TIP: If you are the only one around when you are putting the latches on (like I was), use masking tape to hold the sides together until they are secured together.
TIP: Once youve got the sides fitting the way you want, youll need to remember which side went with which side. Simple. Mark the insides with numbers, letters, or dots.
Click To Enlarge Photo: Greg Holdsworth (All photos)

In my ever-evolving quest to improve my composting skills, I am always excited to try new things. In this case, it was a new compost bin design. To properly turn a pile, it may be more convenient or easier to remove the bin first, turn the pile, then put the material back into the bin. That's where this design excels - the sides are held together by hook-and-eye latches, which make it very easy to take the sides apart. When you are done composting for the year (are your ever really done?), the sides can be conveniently stored. The other advantage is that it provides air circulation on almost 100% of its surfaces. This project will produce a compost bin one cubic yard in size, which is the minimum recommended size for efficient breakdown of organic material.


The list of things you'll need:

Lumber & Supplies
• 24 pieces of 2" x 2" x 36" wood furring strips (I used eight 2" x 2" x 8' pieces)
• 4 pieces of 36" x 39" hardware cloth, with 1/2" squares (I had to get two 3' x 10' rolls)
• 60 - 3" deck screws (a 1-pound box will give you more than enough)
• Box of galvanized metal staples (I used the Arrow 5/16" size)
• 8 - 2 1/2" gate hook-and-eye latches (they should include the matching screw eye piece)
• Masking tape (optional)
• Business card (optional)

Tools
• Saw (circular saw strongly recommended)
• Drill and drill bits
• Pencil and tape measure
• Square (metal or fast plastic type)
• Sandpaper or sanding block
• Hammer
• Awl, nail or other pointed-end tool
• Staple gun
• Tin snips or other wire cutters
• Pliers


Skill Level:

Intermediate


Construction:

1. The 2" x 2" wood furring strips were available in 8-foot-long pieces, so I cut 24 pieces that were 36" long.

2. As a result of STEP 1, you may have about eight 24" pieces left over. This is good because you will need 16 pieces with 45-degree angled cut ends measuring 18" long. Using the remaining 2" x 2" x 8' wood furring strips, cut the remaining eight 18"-long pieces. 

3. Cut a 45-degree angle on both ends of the 18" long pieces.

You should now have 16 pieces total measuring 36" long, and 16 pieces (corner braces) measuring 18" long with 45-degree angled ends (PHOTO A).

4. Build the first side panel by screwing four of the 36" long pieces together at the ends. You will want to pre-drill the holes before setting the screws (PHOTO B). Repeat this step to build the other three side panels. 

5. Screw four corner braces to the side panel assembled in STEP 4 (PHOTO D). Tip: In order to get the proper angle of the screw, draw a line on the two pieces of wood to act as a guide when you are pre-drilling the holes (PHOTO C). Repeat this step with the other three side panels. 

6. Cut out four pieces of the 36" hardware cloth. Staple the piece of hardware cloth to the wood side panel, making sure there isn't any overlap. In other words, make sure the hardware cloth isn't going past the outside edge of the side panel. Repeat this step for the other three side panels. Tips: Sand down the side panel before stapling the hardware cloth to it. Also, staple each corner of the hardware cloth down first. This will keep the piece from moving while you put in the rest of the staples along the edges. 

7. Put a pencil mark 6" from the edge of the side panels, so that the hook-and-eye latches are spaced consistently. 

8. Using the back of a business card as a template, mark two spots 2 1/4" apart. This card can be used as a template to mark the two holes on the side panel, using an awl, nail, or other pointed object (PHOTO E).

9. After pre-drilling the holes, screw in the hook-and-eye latches and corresponding screw eye pieces (PHOTO F).

At this point, your compost bin is basically finished (PHOTO G). You can take the side panels apart, take the bin to where it will be located, and finally, put the panels back together. 

 

 


After you try it, show it off to other members in the
gardener's gallery.
Post your photos

posted in: compost, diy, Composting, compost bin

Comments (18)

luizamodel writes: Superb work!!
Posted: 2:01 am on May 3rd
LongMMilburn writes: Very innovative idea for protecting your plants! Thanks for sharing such helpful post.
Posted: 4:04 am on April 21st
Nathan_Burris writes: Beautiful.....
Posted: 8:59 am on October 27th
Emily_Rose writes: Awesome way to protect your plants...
Posted: 3:08 am on October 27th
LeonPorter writes: Thanks for the kind review, I appreciate it!

Posted: 6:32 am on October 26th
CharlesFrasor writes: Its fanastic and look very beautiful.

Posted: 6:11 am on October 26th
SteafenRoid writes: It's the perfect
Posted: 12:49 am on October 26th
RandFish writes: Good collection
Beautiful glossary

Posted: 3:02 am on October 23rd
BenjaimWelch writes: Good collection

Posted: 2:48 am on October 22nd
KodecRex writes: Out standing
Posted: 1:53 am on October 22nd
reesefallon writes:
Posted: 5:49 pm on July 15th
reesefallon writes:
Posted: 5:49 pm on July 15th
reesefallon writes:
Posted: 5:49 pm on July 15th
reesefallon writes:
Posted: 5:49 pm on July 15th
reesefallon writes:
Posted: 5:49 pm on July 15th
reesefallon writes:
Posted: 5:49 pm on July 15th
reesefallon writes:
Posted: 5:49 pm on July 15th
reesefallon writes:
Posted: 5:49 pm on July 15th
Log in or create a free account to post a comment.